Lost your Pontiac G6 car remote or need to program a new one? Instead of heading straight to the dealership and spending a hefty sum, you can actually program your remote yourself at home. This guide provides you with step-by-step instructions to program your Pontiac G6 remote, saving you time and money. This process is surprisingly straightforward and requires no special tools.
Step-by-Step Programming Instructions for Your Pontiac G6 Remote
Follow these simple steps to program your key fob for your Pontiac G6. Make sure to read each step carefully before proceeding.
-
Get Comfortable in the Driver’s Seat (or Passenger Seat): Start by getting into your Pontiac G6. While the instructions mention the driver’s seat, some users find it easier to perform these steps from the front passenger seat. Choose whichever is more comfortable for you.
-
Remove the Ignition Key: Ensure the ignition key is removed from the ignition lock cylinder.
-
Close All Doors: Make sure all doors of your Pontiac G6, including the trunk, are completely closed.
-
Locate and Remove the MALL PGM Fuse: You’ll need to access your fuse panel, typically located inside the car, often under the dashboard or in the glove compartment. Refer to your Pontiac G6 owner’s manual to pinpoint the exact location of the fuse panel and the MALL PGM fuse. Once located, carefully remove this fuse.
-
Turn the Ignition to ACC: Insert your key into the ignition and turn it to the ACC (Accessory) position. This is usually the first position after OFF.
-
Cycle Ignition ACC and OFF Quickly: Turn the ignition from the ACC position back to OFF, and then back to ACC again within one second. This quick cycling is important for initiating the programming sequence.
-
Open and Close Any Vehicle Door: Open and then close any door on your Pontiac G6. This action helps trigger the system to enter programming mode.
-
Listen for the Chime: After closing the door, listen carefully for a chime. This chime indicates that the remote control door lock receiver has successfully entered the programming/diagnostic mode. If you don’t hear a chime, you’ll need to go back to step 1 and repeat the process. It’s crucial to hear this chime to proceed.
-
Press and Hold LOCK and UNLOCK Buttons: Take the remote transmitter you wish to program. Simultaneously press and hold down both the LOCK and UNLOCK buttons on the remote for approximately 14 seconds.
-
Program Additional Transmitters (If Needed): If you have additional remotes to program, repeat step 9 for each transmitter. You can program up to 4 transmitters using this procedure. Remember that programming a new transmitter will erase any previously programmed transmitters, so you must program all of your remotes at once.
-
Remove the Ignition Key: Once you have programmed all your remotes, remove the ignition key from the ignition lock cylinder.
-
Reinstall the MALL PGM Fuse: Go back to the fuse panel and reinstall the MALL PGM fuse in its original location.
-
Test Your Remotes: Finally, test each of your newly programmed remotes to ensure they are working correctly. Press the lock and unlock buttons to verify that they control the door locks as expected.
Alt text: A close-up of a Pontiac G6 key fob, highlighting the lock and unlock buttons used during the car remote programming procedure.
Important Programming Notes
- Erase Previous Programming: Be aware that when the keyless entry receiver enters programming mode, it erases all previously programmed transmitter information. Therefore, you must program all of your remotes during a single programming session, even the ones that were working before.
- Program One Vehicle at a Time: If you are programming remotes for multiple vehicles, program them one at a time. Programming remotes for multiple vehicles simultaneously could lead to a transmitter being incorrectly programmed to more than one vehicle.
- Timing is Key: The timing in steps 6, 7, 8, and 9 is important. Make sure to follow the timeframes as closely as possible for successful programming.
- Verify Operation: After programming, always validate that all programmed transmitters are functioning correctly. This ensures that the programming process was successful for each remote.
By following these instructions, you can easily program your Pontiac G6 car remote yourself, avoiding unnecessary expenses and getting you back on the road with a working key fob.
