Integrating your car’s built-in remote system with your Genie garage door opener offers unparalleled convenience. No more fumbling for a separate remote – with systems like HomeLink and Car2U, your garage door opens with the press of a button already in your car. These in-car technologies, typically found on your visor or overhead console, operate on your vehicle’s power, eliminating the need for batteries. Genie garage door openers are designed to be fully compatible with both HomeLink and Car2U. HomeLink systems are identifiable by a single LED indicator and often a house icon on the center button. Car2U systems feature three LED lights, one above each button.
This guide provides clear, step-by-step instructions on how to program your car garage door opener Genie system using both HomeLink and Car2U.
Programming Your HomeLink System for Genie Garage Door Openers
HomeLink is a widely used system for integrating garage door openers and other home automation devices into your vehicle. Here’s how to program it for your Genie opener:
Step 1: Clear Existing HomeLink Programming
Before programming a new garage door opener, it’s good practice to clear any previous settings. To do this:
- Press and hold the first and third buttons on your HomeLink system simultaneously.
- Keep holding until the indicator light blinks slowly and then rapidly. This should take about 20 seconds.
- Release both buttons. Clearing the HomeLink ensures a clean slate for programming your Genie garage door opener. Note that this process will erase all previously programmed devices.
Step 2: Teach HomeLink Your Genie Remote Signal
Next, you need to train your HomeLink system to recognize the signal from your Genie garage door remote.
- Choose the HomeLink button you want to use for your Genie garage door.
- Position your Genie remote approximately two inches away from the chosen HomeLink button.
- Press and hold the button on your Genie remote.
- While still holding the Genie remote button, press and hold the selected HomeLink button.
- Continue holding both buttons until the HomeLink indicator light changes from a slow blink to a rapid blink.
- Once the rapid blinking begins, release both buttons. Your HomeLink system has now learned the frequency from your Genie remote.
Step 3: Synchronize HomeLink with Your Genie Opener
The final step involves syncing your programmed HomeLink button with your Genie garage door opener unit. The process varies slightly depending on whether you have a newer or older Genie model.
For Newer Genie Garage Door Openers (with a Program Button):
- Locate the PROGRAM button on your Genie garage door opener motor unit (powerhead). Press and hold it until a round blue LED illuminates. Release the button. A long purple LED will start flashing.
- In your car, press and hold the HomeLink button you programmed in Step 2 for two seconds, then release. Repeat this press-and-release sequence a second time. The long LED on your Genie opener will flash blue and then turn off.
- Test the connection by pressing the HomeLink button again. Your garage door should now activate. If it doesn’t, repeat step 2 and this step.
For Older Genie Garage Door Openers (with a Learn Button):
- Find the learn code button on your Genie garage door opener powerhead. Press and release this button. A red LED will start blinking.
- Press the programmed HomeLink button in your car one time. The red LED on the opener should stop blinking and remain on.
- Press the HomeLink button a second time. The red LED should turn off.
- Press the HomeLink button again to test. Your garage door should now respond and open or close.
For further assistance, consult your vehicle’s owner’s manual, visit www.homelink.com, or the Genie Company website at www.GenieCompany.com.
Programming Your Car2U System for Genie Garage Door Openers
Car2U is another in-car system that provides remote control for garage doors and gates. Here’s how to program it to work with your Genie garage door opener:
Step 1: Reset Car2U to Factory Default Settings
Car2U systems come with factory default settings where button 1 is pre-set for Genie openers. However, resetting ensures a clean programming process.
- Press and hold buttons 1 and 3 on your Car2U system simultaneously for 20 seconds.
- Continue holding until all three LED indicators start flashing.
- Release both buttons. The Car2U system is now reset to its factory default settings. This will clear any previously programmed garage door openers.
Car2U buttons in a car for operating garage door. Alt text: Car2U in-car remote control buttons, used for operating Genie and other garage door opener brands from inside vehicle.
Step 2: Program Car2U to Recognize Your Genie Opener
Now, program your Car2U button to communicate with your Genie garage door opener.
For Newer Genie Models (with a Program Button):
- Locate the PROGRAM button on your Genie opener powerhead. Press and hold it until the round blue LED turns ON. Release the button. The long purple LED will begin to flash.
- Press and hold the Car2U button you wish to program for your Genie opener for two seconds, then release. Repeat this press-and-release sequence one more time. The long LED on the Genie opener will flash blue and then turn off.
- Test by pressing the Car2U button a few more times until your garage door moves.
For Older Genie Models (with a Learn Button):
- Press and release the learn code button on your Genie garage door opener powerhead. The red LED will begin to blink.
- Press your desired Car2U button one time. The red LED will stop blinking and stay illuminated.
- Press the same Car2U button one more time. The red LED should turn off.
- Press the Car2U button again to test. Your garage door should now operate.
Step 3: Changing Factory Default Button for a Genie Opener (If Needed)
If you want to use button 2 or 3 for your Genie opener (button 1 is default Genie), follow these steps:
- Press and hold buttons 1 and 3 for just ONE SECOND and release. All three LEDs will light up solid red.
- Press and hold the button you want to set for Genie (button 2 or 3). The corresponding LED will flash. While still holding this button, press and release button 1, and then press and release button 1 again.
- Release the button you held in step 2 and wait for the LED to stop flashing. This button is now programmed for your Genie opener. Repeat Step 2 if you have a second Genie opener to program to another Car2U button.
For additional support, refer to your vehicle’s manual, visit learcar2u.com, or www.GenieCompany.com.
By following these instructions, you can easily program your car’s built-in system to control your Genie garage door opener, adding convenience and security to your daily routine.